Showing results: 676 - 690 of 1039 items found.
-
O Series -
Bowman
The O Series combines high performance with a small x-ray spot size. This is made possible by the poly-capillary focusing optics system that replaces the collimator assembly installed in standard Bowman systems. The optics are designed to focus the x-rays coming from the tube exit window to a very small spot size (80μm FWHM) while retaining virtually 100% of the tube flux. So instead of attenuating the x-rays that can’t fit through the small apertures, as is the case with collimator systems, the poly-capillary optics assembly allows almost all of the x-rays from the tube to reach the sample. The result is much greater sensitivity for testing very small components or thin coatings. Shorter test times can achieve even better repeatability when comparing optics systems vs. a similar sized collimator.
-
M9451A -
Keysight Technologies
The M9451A PXIe Measurement Accelerator combined with Option DPD Digital Pre-Distortion & Envelope Tracking Gateware shows what is possible when you combine state of the art FPGA's with Keysight's trusted measurement expertise and PXIe's high speed data handling. As part of Keysight's RF PA/FEM Characterization & Test, Reference Solution, this combination provides unprecedented performance for demanding envelope tracking and digital pre-distortion measurements required for testing modern power amplifiers (PAs) and front-end modules (FEMs). Hardware acceleration provides better than 20x speed improvement over Keysight's previous host-based Reference Solution, with closed/open loop digital pre-distortion (DPD) and envelope tracking (ET) measurements taking just tens of milliseconds and overall measurement times less than 70 ms.
-
Model 7650 -
Jinan Testing Equipment IE Corporation
Model 7650 extensometers are primarily used on round specimens tested in bi-axial test machines capable of simultaneous axial and torsional loading. All models are capable of bi-directional displacement in both axes and may be used for strain-controlled fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7650 models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to minimize crosstalk between axes and to provide high accuracy, high resolution measurements. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods with conical rod tips for specimen contact when testing to 1200℃(2200°F). Silicon carbide rods are used for the 1600℃ (2900°F) high temperature option.
-
GM8042 -
UC Instruments, Corp.
The GM8042 desktop tunable laser sources offer superior performance in testing DWDMcomponents, AWG & PLC components, optical amplifiers, DWDM system and performing other general-purpose fiber optical test and measurement applications. It is a high wavelength accuracy, high power output, compact dimensions, fast startup, and affordable tunable laser source system. UC INSTRUMENTS provides C band, L band, or C+L band tunable laser sources options.
-
Santa Barbara Infrared, Inc.
SBIR offers an extensive line of reliable, high performance test equipment used to characterize and calibrate IR, Visible and Laser systems. Products include blackbodies, visible sources, target wheels, targets, collimators, target projectors, laser test modules/systems and IRWindows™ software for automated testing. These modular, cost effective instruments are user-friendly and easily integrated into automated test systems. For more information, including printable data sheets, select a product from the list.
-
QT 200 NXG -
Qmax Test Technologies Pvt. Ltd.
QT 200 Nxg a Highly sophisticated ATE, is now available as a desktop unit with the cost, flexibility, and performance demanded by a large number of users in research, design, manufacturing, and repair & maintenance industry. It is a combinational-mixed signal board tester for PCBAs designed to cater the needs of PCB test and repair depots, keeping in mind the changing PCB technology and challenges in testing them offline with the combination of all such complex test methodologies in a single test hardware platform with simple to use graphical user interface software.
-
Model 7651 -
Jinan Testing Equipment IE Corporation
Model 7651 extensometers measure combined in-plane strains in flat cruciform specimens tested in machines capable of simultaneous X and Y (perpendicular) axial loading and on standard flat samples tested in pure tension. All models are capable of bi-directional displacement in both axes and may be used for strain-controlled fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7651 models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to eliminate crosstalk between axes and to provide high accuracy, high resolution measurements. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods with conical rod tips for specimen contact when testing to 1200℃(2200°F). Silicon carbide rods are used for the 1600℃(2900°F) high temperature option.
-
ImageMaster PRO 10 -
Trioptics GmbH
As a result of various improvements the ImageMaster® PRO 10 enables customers to significantally increase their yield. It is the fastest and most accurate MTF measurement system on the market for qualifying mobile phone lenses and other miniature lenses. Besides the new software architecture and functions, the more precise mechanical components lead to best performance in accuracy, reliability and measurement speed. Faster MTF algorithms reduce the test cycle time so that an outstanding throughput is achieved. The ImageMaster® PRO 10 features a 15% increased productivity compared to the ImageMaster® PRO 9.The new ImageMaster® PRO 10 also provides additional measurement functions. For example, measurements at different frequencies and RGB measurements can be performed to determine chromatic aberration. An upgrade of four additional cameras allows the measurement of relative illumination for testing the homogeneous illumination of lenses in the field.
-
TP121-TH -
Gigahertz-Optik GmbH
The photometric specifications of LEDs must meet very high tolerance requirements regardless of whether they are to be used in general, automotive or other specialist lighting applications. This is often a problem since the manufacturing tolerances of LEDs can be higher than those permitted in the end-use applications. Also, LED binning by LED manufacturers in order to classify LEDs based on their tolerances is performed with flash mode testing using pulsed current flow. However, end-use applications of the LEDs often operate in constant current mode and with significant thermal effects. The sophisticated LED processing industry therefore requires measurement devices that can be used for both manufacturer-compliant pulsed mode, as well as constant current operation mode. When the LEDs are run in constant current mode, the junction temperature has significant influence on the performance and lifetime of the LED. Therefore, test systems should be able to test the LEDs at specific junction temperatures.
-
SERIES 6000 -
Polatis, Inc.
The Polatis Series 6000 Network Optical Switch is a high-performance, fully non-blocking all-optical matrix switch available in sizes from 8x8 up to 192x192. It is designed to meet the highest performance and reliability needs of the most demanding applications with exceptionally low optical loss, compact size, low power requirements and fast switching speeds. With support of Software-Defined Networks (SDNs) via an embedded NETCONF and RESTCONF control interfaces, the Series 6000 enables extremely low latency for time-critical traffic required for new virtual cloud services in hybrid packet-optical data centers. The Series 6000 is based on Polatis’ patented DirectLight® optical switching technology that has been proven in the most challenging data center, telecom and defense applications and is also used by major network equipment manufacturers to automate testing of optical components and subsystems.
-
imc Test & Measurement GmbH
Electric drives such as DC and EC motors are more and more extensively deployed in the automotive industry. At the same time there is an increasing requirement for a 100% analysis of motors for fault detection and error analysis as well as statistics on quality, without increasing production cycles times. The model-based Parameter Identification method (PI method) from imc allows testing to be performed under load, yet without an “explicit” separate load machine. Instead, the motor is loaded dynamically by exploiting its own inherent inertia. This allows motor parameters such as resistance, inductivity and friction to be determined within a few seconds. A mathematical model and its parameters reflect motor behaviour in its completeness and make it possible to monitor motor production based on limit values and trend statistics. The identified parameters of the model equation can then be used to calculate derived key performance indicators of the motor characteristic curve.
-
MESA-50 -
HORIBA, Ltd.
HORIBA has been selling the XGT-WR series of EDXRF analyzers for many years, providing screening measurements of samples containing hazardous elements such as Pb, Cd, Hg, Cr, Br, Sb, As for RoHS, ELV, and Cl for halogen free applications.XGT systems are used daily throughout the world. HORIBA has now developed the new MESA-50 EDXRF analyzer, based on its long experience with customer requirements and knowledge. MESA-50 provides user friendly operation and good performance. MESA-50 includes three analysis diameters, suitable for every sample, from thin cables and electronic parts to bulk samples. The combination of SDD detector and Digital pulse processor(DPP) changes the image of EDXRF.HORIBA's new MESA-50 supports ecological procurement; it contributes not only to EU RoHS and ELV compliance testing, but also regulatory work for many other countries.
-
SCR ELEKTRONIKS
SCR ELEKTRONIKS have developed TESTING SET UP FOR SINGLE PHASE / THREE PHASE MOTOR for carrying out Performance Test, Earth Contact Resistance Test, High Voltage Test, Megger Test and Leakage Current Test. It consists of Voltmeters, Ammeters and Wattmeters for observing the values of different parameters. OK / NOT OK lamps are also provided to display the results of Earth Contact Resistance Test, HV test, Megger Test, Leakage Current Test. All tests are provided with tripping cut off concept.
-
8130A -
TSI Inc.
The Automated Filter Tester Model 8130A continues to be the best solution for testing particulate respirator filters, disposable filtering face pieces, and a wide assortment of filter media. The TSI filter testers have been used in quality control and manufacturing by leading filter and filter media manufacturers and test centers around the world for more than 20 years. Based on TSI's established model 8130, the world's most-used filter tester, model 8130A now offers higher sensitivity and resolution - up to 99.9999 percent efficiency - at a lower cost of ownership due to the new serviceable photometers inside. The model 8130A features a high degree of automation and self-diagnostics that greatly simplifies operation, increases throughput, and improves overall measurement performance. Whether looking for a stand-alone tester to check a few filters per day or need to integrate a tester in an automated, high-volume production line, the model 8130A is up to the challenge.
-
TP500110 -
Total Phase Inc.
The Promira™ Serial Platform is our most advanced serial device ever. This new, powerful platform offers many benefits over our previous generation of host adapters:*Integrated level shifting ensures you'll be able to work at a variety of voltages ranging from 0.9 to 5.0 volts without needing any costly accessory boards.*High-speed USB connectivity to the host system provides high performance and convenience for benchtop programming, testing, and emulation.*Ethernet connectivity is convenient for benchtop work, and it also enables remote control for your automation needs.*With the ability to provide a total of 200 mA of power, Promira platform can easily power your project, simplifying connectivity and troubleshooting.*New architecture enables you to download applications to the Promira platform - Upgrade your device when you need new features and you'll never wait for that emergency delivery in the middle of your project.
